Page 17 - Fireless
P. 17
ELESS PRODUCT GUIDE
3. A message ‘Waiting for new device’ is given.
4. Immediately press the START button of the field device for 3 seconds. If the device is functioning
correctly and is within range, the screen will change to show the physical characteristics of the device
to be added as shown above. PHY addresses and type should match. Note: Once the search process has
been initiated, the field device start button must be pressed and found within 10 seconds, otherwise
the search routine will time-out and it will be necessary to cancel and re-start the ‘add new device’
sequence.
5. The system will automatically assign the next available free address location and a default type code
‘OPT’. The address line will now be highlighted. If this is acceptable, press the > scroll button followed
by ACCEPT. Otherwise, continue to follow the procedure below to manually select another free address
and/or alternative type code. Note: The type code chosen must match the type of detector head being
fitted to the base.
6. Use the < > scroll buttons until the ‘logical address’ or ‘Type’ line is highlighted, then press OK. The
highlight will now reduce in size to highlight the parameter to change.
7. Use the scroll buttons to make the necessary changes, followed by OK.
8. When finished, Press the scroll buttons until ACCEPT is highlighted, followed by OK.
Note: All address and type code changes must be completed and the device Accepted within 1 minute of
pressing the field-device start button, otherwise the end-point will time out and return to its default factory
state.
6.9 Delete device
Press OK or < > to scroll past.
Use this menu to delete an unwanted device from the transponder.
1. The logical address line will be highlighted.
2. Press OK to highlight the address field.
3. Press < > until the address of the device to delete is reached, followed by OK.
4. Press > to highlight DELETE, followed by OK.
5. Remove the physical, unwanted device from its base or fixing and, prior to removing its batteries, PRESS
its START button for 15 seconds in order to return it to factory default. Note: if this is not done, the
device will continue to transmit its data to the transponder, which will reported periodically as a ‘UNS’
event within the event log.
6.10 System administration
Press OK to enter or < > to scroll past.
This menu should be accessed if the transponder password needs to be changed; it also allows the engineer
to manually Reset or Silence the transponder, if necessary, during service visits.
1. Press < > until the required field/line is highlighted, followed by OK.
2. If ‘Change Password’ is selected, use the arrows keys to enter the OLD and NEW passwords, followed by
OK.
Note: Be sure to check and make a note of the new password before saving, as it is not possible to retrieve it
or reset to factory default afterwards.
Document No.: PEN-FL2-2 Date: 29/06/2016 Page 17 / 30
3. A message ‘Waiting for new device’ is given.
4. Immediately press the START button of the field device for 3 seconds. If the device is functioning
correctly and is within range, the screen will change to show the physical characteristics of the device
to be added as shown above. PHY addresses and type should match. Note: Once the search process has
been initiated, the field device start button must be pressed and found within 10 seconds, otherwise
the search routine will time-out and it will be necessary to cancel and re-start the ‘add new device’
sequence.
5. The system will automatically assign the next available free address location and a default type code
‘OPT’. The address line will now be highlighted. If this is acceptable, press the > scroll button followed
by ACCEPT. Otherwise, continue to follow the procedure below to manually select another free address
and/or alternative type code. Note: The type code chosen must match the type of detector head being
fitted to the base.
6. Use the < > scroll buttons until the ‘logical address’ or ‘Type’ line is highlighted, then press OK. The
highlight will now reduce in size to highlight the parameter to change.
7. Use the scroll buttons to make the necessary changes, followed by OK.
8. When finished, Press the scroll buttons until ACCEPT is highlighted, followed by OK.
Note: All address and type code changes must be completed and the device Accepted within 1 minute of
pressing the field-device start button, otherwise the end-point will time out and return to its default factory
state.
6.9 Delete device
Press OK or < > to scroll past.
Use this menu to delete an unwanted device from the transponder.
1. The logical address line will be highlighted.
2. Press OK to highlight the address field.
3. Press < > until the address of the device to delete is reached, followed by OK.
4. Press > to highlight DELETE, followed by OK.
5. Remove the physical, unwanted device from its base or fixing and, prior to removing its batteries, PRESS
its START button for 15 seconds in order to return it to factory default. Note: if this is not done, the
device will continue to transmit its data to the transponder, which will reported periodically as a ‘UNS’
event within the event log.
6.10 System administration
Press OK to enter or < > to scroll past.
This menu should be accessed if the transponder password needs to be changed; it also allows the engineer
to manually Reset or Silence the transponder, if necessary, during service visits.
1. Press < > until the required field/line is highlighted, followed by OK.
2. If ‘Change Password’ is selected, use the arrows keys to enter the OLD and NEW passwords, followed by
OK.
Note: Be sure to check and make a note of the new password before saving, as it is not possible to retrieve it
or reset to factory default afterwards.
Document No.: PEN-FL2-2 Date: 29/06/2016 Page 17 / 30
